After the power is turned on, there is no “drop†called?
1. Check if the power supply output voltage is normal. If not, replace the power supply.
2. Check if the power supply is properly connected to the host. If not, reconnect the power supply;
The switch door is not continuous and smooth, and there is jitter?
1. Check whether the power load can drive the electronic lock and the motor, if not, replace the power supply;
2. Check the thickness of the connecting line between the power output line and the input line of the door opener. If the line is thin, replace the thick line (you cannot use the network cable);
3. After the power is cut off, confirm that the door body can be smoothly pushed by hand without obvious resistance. If there is obvious resistance, please re-adjust the installation position of the door opener;
4. Power on, please increase the resistance sensitivity F9 or decrease the opening speed and closing speed;
After the door is opened, the door keeps shaking?
Whether the green function line (on/off button line) is connected to the chassis (or the common terminal) for a long time. If the door shake phenomenon is inevitable, please disconnect it;
The remote control is not working?
1. Confirm that there is a battery in the remote control and the battery is fully charged. If there is any problem, please change the battery;
2, let the remote control leave the door machine far away, and then remote control;
3, open the cover according to the remote control learning process to re-learn the remote control;
Can the electronic lock not be locked or unlocked smoothly?
1. Confirm that the electronic lock is the same as the system setting lock. If it is different, please adjust the lock type.
2. If the door cannot be locked: if the door is not in place, please turn up the locking force of the door or turn the door buffer down or turn the door closer to the door, so that the door can be closed smoothly;
3. If the door cannot be unlocked: Please turn the unlocking time to increase the opening time, and give the electronic lock enough time to disengage;
4. Confirm whether the electronic lock is damaged. If it is faulty, please change the electronic lock with good function;
The door can't always open to the setting angle?
1. Horizontal movement adjusts the relative position of the door opener and the door shaft;
2. Please reset the output shaft rotation angle;
Cannot close automatically after opening the door
1. Confirm whether it works in the normally open mode. If yes, please switch to the very open mode.
2. Confirm whether there are signals in the two green channel ports, and if so, cancel the signal;
If the door switch is irregular, please reset the starting point and opening direction. If it cannot be solved, please consult the manufacturer;
Warning
1. Attention! Follow the instructions carefully, which is very important for personal safety. Incorrect installation or misuse of the product may cause serious damage to people and property;
2. Please read the instructions carefully before installing the product;
3. Save the instructions for future use;
4. Do not install this product in areas with explosion hazards; flammable gases are serious safety hazards;
5. Mechanical parts must comply with relevant national standards;
6. The installation must comply with the relevant national regulations;
7. The power should be cut off before the system is overhauled;
8. Check that the grounding system is correct;
9. Parts not manufactured by the company are installed in the system. If there is a safety problem and it is not working properly, the company is not responsible;
10. Repair only the original part;
11. Do not make any changes to the components of the system;
12. The installer must provide the user with detailed instructions on the operating methods and emergency conditions, and provide the product description to the user;
13. Children and other unrelated persons are strictly prohibited from approaching when installing the product;
14. Place the remote control out of the reach of children to prevent accidents;
15. It is strictly forbidden for users to try to repair or adjust the system by themselves.
16. Nothing specified in the manual is not allowed;
Plastic A Board
1. Durable: Plastic A Boards are made of high-quality plastic material that is durable and long-lasting, making them ideal for outdoor use.
2. Lightweight: Plastic A Boards are lightweight and easy to move around, making them perfect for businesses that need to change their signage frequently.
3. Waterproof: Plastic A Boards are waterproof, which means they can withstand rain, snow, and other harsh weather conditions without getting damaged.
4. Double-sided: Plastic A Boards are double-sided, which means you can display your message on both sides, making them more visible to passersby.
5. Easy to clean: Plastic A Boards are easy to clean and maintain, requiring only a damp cloth to wipe them down.
6. Customizable: Plastic A Boards can be customized with your business logo, message, or any other design you wish to display.
7. Affordable: Plastic A Boards are affordable compared to other types of signage, making them a cost-effective advertising solution for businesses of all sizes.
Plastic A Board,Board Plastic,Plastic Face Boards,Plastic Panel
SUZHOU JH DISPLAY&EXHIBITION EQUIPMENT CO.,LTD , https://www.jh-rollup.com
![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)