FESTO cylinder load increase and decrease too fast, especially rapid start, stop and change in operating conditions when the temperature changes, the warm cylinder is not the correct way, open the insulation layer too early shutdown, etc., in the cylinder (cylinder) and law Blue produces great thermal stress and thermal distortion.
1.Festo FESTO cylinders are cast and cylinders are subjected to aging treatment after leaving the factory, so that the internal stress generated by the cylinder during the casting process is completely eliminated. If the aging time is short, then the processed cylinder will be deformed in the subsequent operation.
2. The force of the Festo FESTO cylinder during operation is very complicated. In addition to the pressure difference between the gas inside and outside the cylinder and the isostatic load of the various components contained therein, it is also necessary to withstand the static part when the steam flows out of the stator vane. The reaction force, as well as the force applied to the cylinder in the cold and hot state of various connecting pipes, under the interaction of these forces, the cylinder is prone to plastic deformation and causes leakage.
3. Festo FESTO cylinder load increase and decrease too fast, especially rapid start, stop and change in operating conditions when the temperature is large, the warm cylinder is not the correct way, open the insulation layer when shutdown and maintenance is too early, in the cylinder And on the flange there is a lot of thermal stress and thermal deformation.
4. Festo FESTO cylinders produced stress during machining or after welding, but they were not eliminated by tempering the cylinders, resulting in large residual stresses in the cylinders and permanent deformation during operation.
5. During the installation or overhaul process, due to the overhaul and overhaul techniques, the expansion gaps of the inner cylinder, cylinder spacers, spacers and steam jackets are not suitable, or the expansion gaps of the mounting lugs are not suitable. After operation, a huge expansion force is generated to deform the cylinder.
6. The cylinder sealant used is of poor quality, excessive impurities or the wrong type; if there are hard particles in the sealant of the cylinder, the sealing surface will be difficult to be tightly combined.
solution:
1.Festo Festo cylinder deformation or leakage of the serious combination of the surface, using the method of scraping the joint surface
If the upper cylinder surface is deformed in the range of 0.05mm, the upper cylinder joint surface is used as the reference surface, and reddened or embossed blue paper is coated on the lower cylinder joint surface, and the lower cylinder is scratched according to the trace. If the deformation of the upper face of the cylinder is large, apply red dan on the upper cylinder, and use a large flat rule to remove the marks and flatten the upper cylinder. Or take the mechanical processing method to level the upper cylinder joint surface, and then use the upper cylinder as a reference to scrape the lower cylinder joint surface. There are two general methods for scraping the cylinder joint surface:
(1) Bolts that are not tightly coupled to the surface are used to push the upper cylinder back and forth slightly with the jack, and the scraping is performed according to the situation of the red cylinder of the lower cylinder joint surface. This method is suitable for high-rigidity high-pressure cylinders.
(2) It is a bolt with a tight joint surface. According to the tightness of the inspection joint surface of the feeler gauge, the value and the pressed-out trace are measured and the joint surface is repaired. This method can eliminate the influence of the cylinder arc on the clearance.
2. Use proper cylinder seal material
Because there are no unified national standards and industry standards for turbine sealants for turbines, the production materials and formulations are also different, and the quality of products is uneven. When selecting a turbine sealant for cylinders, it is necessary to choose a reputation in the industry and product quality. A guaranteed regular manufacturer to ensure the tightness of the cylinder after overhaul.
Manual Saw Blade Pipe Cutting Machine
1. Servo motor driving feeding system with AC servo motor / C5 level ball guide screw and linear guide rail, fast, stable and accurate. Maximum feeding speed of 1000mm / s and feeding length of 1000m, multiple feed.
2. Gearbox driving Saw Blade, is produced by casting and processing by CNC machining center, which is stronger and more accurate. Inside, the core components of gearbox are imported from Taiwan, which produced with advanced milling and vacuum heat-treatment, so they are precise and long lifetime, lower noise and high transmission efficiency. Saw blade can work stable and process in long lifetime.
3.The special designed clamp has strong clamping capacity, firm, safe and reliable.
4. Automatic circulation of coolant ensures smooth cutting surface and long service life of saw blade.
5. Great Clamping device of pipes can decrease pipes vibration during working to extend saw blade lifetime and guarantee feeding speed with the Patent No.ZL 2009 1 0039079.8
6. Servo tail processing device, when the material is more than 100mm left, automatically cut the tail, avoiding that after the former automatic pipe cutting machine has finished cutting, the tail should be cut again separately, saving material and labor and improving production efficiency. Min tail length is 20-30mm.
7. Stop gauge is equipped, that used as keeping alignment of pipes and providing original point for system in order to improve preparing time and avoid the mistake of feeding by manual.
8. Control system is developed by Chittak that is with rich database, and can be updated. Easy operate.
9. It is equipped with an automatic detection and alarm information system, which is convenient for users to troubleshoot.
10.Using Mitsubishi PLC controller, the circuit is simple and the maintenance is simple, response is fast.
11.Can set 5 different cutting lengths for a single material to reduce waste of surplus materials.
12.Length digital display and easy setting and operating in control system.
13.The model can be updated with automatic loading system that can greatly improve efficiency and save the labor cost. Meanwhile, it can be equipped with conveyor belt to transport the finished goods to next machine process. All updated functions can be controlled by Cutting Machine System.
Pipe Cutting Machine Blade,Manual Pipe Cutting Machine,Manual Saw Pipe Cutting Machine,Pipe Cutting Machine Saw Blade
GUANGDONG CHITTAK INTELLIGENT EQUIPMENT CO.,LTD , https://www.chittakcutting.com
![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)